ZBoost YX550 VLTE-AWS Guide de l'utilisateur télécharger pdf

BASE UNIT LED INDICATORS

At Initial Power Up Only

After Initial Power Up

Fast Flashing RED

Solid RED

Solid GREEN

Slowly Alternating

RED and GREEN

zBoost is working, but at reduced performance and coverage due to

“non-ideal” setup. Increase the distance between antenna and

amplifier to achieve maximum performance and coverage.

Normal condition at power up.

Indicates insufficient distance between the antenna and the amplifier.

The amplifier is operating at significantly reduced coverage.

System is receiving signals from either the mobile device or the base

station transceiver which are too strong for proper operation.

Fast Alternating

RED and GREEN

followed by no light

The amplifier is disabled.

Solid GREEN

Solid RED

Normal condition

System is receiving signals from either the mobile device or the base

station transceiver which are too strong for proper operation.

Unplug your system and re-orient the Signal Antenna and/or Base

Unit to reduce excessive signal. If LED remains RED after

reconnecting power, contact customer support at 1-800-871-1612.

SETUP OVERVIEW

zBoost

DataBlast

YX550

Rev A

SETTING UP YOUR zBOOST

SIGNAL BOOSTER

The zBoost DataBlast YX550 is designed to provide increased in-building data

coverage, up to 2500 square feet, making it perfect for the home and office. The

zBoost DataBlast supports multiple users and all devices operating on the

Network(s) covered by your model.

• VLTE: Verizon LTE

• AWS: AWS

• VLTE-AWS: Verizon LTE and AWS

• ALTE: AT&T LTE

• ALTE-AWS: AT&T LTE and AWS

Before installing, please note the following important factors in determining your zBoost

performance:

• At least 15 vertical feet is needed between the Signal Antenna (receives the

outside signal) and the Panel Antenna (rebroadcasts the signal indoors). Separation

less than 15 vertical feet will result in decreased performance. See illustration below.

• Keep the Signal Antenna at least 3 feet above any metal.

Boost data transmission in 4 easy steps:

FIRST: Mount the Signal Antenna. Choose a location for the Signal Antenna

using your cell phone to determine the area of strongest signal. The coverage

your zBoost provides is largely determined by the quality of signal received by the

Signal Antenna.

To maximize signal coverage, place the Signal Antenna where you find the strongest

signal (up high or outside) and at least 3 feet above any metal.

IMPORTANT: Incorrectly mounting the Signal Antenna to the mounting bracket (see

figure A) will impede performance. Ensure that the Signal Antenna is properly

positioned in the mounting bracket as pictured below.

To mount antenna to a pole: Attach bottom of antenna to pole bracket as

pictured. Use U-Bolt to secure bracket to pole and fasten.

To mount antenna to a flat surface: Attach bottom of antenna to pole bracket

as pictured. Secure bracket to desired surface using provided screws. Use of

Download the YX550 User Guide at www.Wi-Ex.com

the Saddle and U-Bolt are not necessary for this option.

SECOND: Place the zBoost Base Unit where you want to create a Cell Zone

Assemble the Base Unit and Base Unit Antenna and position the antenna vertically.

This Base Unit uses an omni-directional antenna that delivers signal in a circular

pattern around the antenna. Place the Base Unit in desired location – where you

want to create a Cell Zone™ For the widest possible signal area, it is recommended

that you position the Base Unit near the middle of a room. The Base Unit can be

placed on a flat surface (e.g., a bookshelf, desk, end table, etc.) and performs best

when located at least 4 feet above the floor or approximately the height of a cell

phone when it is typically in use (avoid placing the Base Unit on the floor).

Keep the Base Unit at least 2 feet away from other cords, metal objects or other

wireless devices such as wireless routers or wireless access points. The zBoost

DataBlast performs best when there are no obstructions between the zBoost Base

Unit and your mobile device.

Note: To mount it on an interior wall, first remove the silver bracket from the Base

Unit, mount the bracket to a wall with 2 screws (not provided), then placing the Base

Unit back into the bracket keeping the antenna vertical.

The zBoost SOHO requires at least 15 feet of vertical separation between the Base

Unit and the Signal Antenna. Generally, increasing this distance (up to 40 feet) will

increase the performance and decreasing the distance will limit zBoost performance.

THIRD: Run the provided coaxial cable between the Base Unit and Signal

Antenna. Use the provided 50 feet of RG-59(mini) coaxial cable to connect the

Signal Antenna and the Base Unit. Should you need additional cable length, 15 foot

extensions (Part #: YX030-15w) are available at www.Wi-Exstore.com. Please note:

Cable longer than 65 feet is not recommended.

PACKAGE CONTENTS

zBoost Base Unit with

Silver Mounting Bracket

Base Unit Antenna

Coax Cable

RG-59(mini), 50 ft

Power Supply

Signal Antenna

(2 pieces) and

Mounting Hardware

SETUP OVERVIEW

Setup Overview

User Guide available

at www.Wi-Ex.com

*Note: An 8 inch window entry cable may be needed for this option. It is available for purchase at www.Wi-Ex.com (Part #: YX030-08W)

FOURTH: Connect the zBoost Base Unit to the provided power supply and

plug into a power outlet. When your zBoost system is in place and fully connected,

walk throughout your home or office and verify that you have fast, reliable data

speeds. If the signal strength has improved, your zBoost is working. Remember,

coverage varies based on outdoor signal level, building construction, and antenna

placement. Coverage in adjoining rooms will be reduced by walls and building

materials.

Upon initial power up, a solid GREEN LED should appear indicating normal

conditions. If a RED light appears, adjustments may be needed to optimize

performance. If you find the increased signal coverage is acceptable, however, no

additional adjustments are needed. See LED Indicator section for more information.

Should you desire to improve coverage, you may:

• Relocate the Signal Antenna in order to capture a better signal–higher is better.

• Increase the distance between the Base Unit Antenna and the Signal Antenna.

• Purchase an upgrade antenna available at www.Wi-Ex.com.

Models:

• VLTE

• AWS

• VLTE-AWS

• ALTE

• ALTE-AWS

Figure A

DataBlast Base Unit

Power Supply

Base Antenna

Coaxial Cable

Signal Antenna

Cell Tower

15 ft

separation

ure A

ata

e Antenna

ration

Pole Bracket

Saddle

U-Bolt

1 2

Résumé du contenu

Page 1 - SETUP OVERVIEW

BASE UNIT LED INDICATORSAt Initial Power Up OnlyAfter Initial Power UpFast Flashing REDSolid REDSolid GREEN Slowly Alternating RED and GREEN zBoost i

Page 2 - WARRANTY INFORMATION

For questions or assistance, contact Wi-Ex customer service at 1-800-871-1612 or email [email protected] 1 YEAR WARRANTY | REGISTER AT WWW.W

Commentaires sur ces manuels

Pas de commentaire

ZBoost YX550 VLTE-AWS Guide de l'utilisateur

Naviguer en ligne ou télécharger Guide de l'utilisateur pour Amplificateurs de signaux cellulaires ZBoost YX550 VLTE-AWS. zBoost YX550 VLTE-AWS User guide Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs de signaux cellulaires ZBoost YX550 VLTE-AWS