ZBoost ZB540 Manuel d'utilisateur télécharger pdf (Page 6)

zBoost CONNECT™ ZB540 Manual zBoost CONNECT™ ZB540 Manual

4 5

Setting Up Your zBoost Signal Booster

The CONNECT boosts signal for a desktop area up to one room of coverage. - making it perfect for

apartments, condos and lofts. No outside antenna placement is required.

Boost voice and data transmission and improve call clarity in 4 easy steps:

FIRST: Place the Signal Antenna on the interior of a window located in the area

of best signal

Determine the location that provides the strongest signal using the signal strength indicator on your

cell phone. Find the location on the window that provides the most bars of signal strength. Before

proceeding, make sure that the intended surface is clean and clear of any dust. Then choose the

suction cup attachments appropriate for your setting (short or long), fasten to the Signal Antenna,

and secure to your window.

Please note: Energy-efﬁ cient windows will likely block signal from reaching the Signal Antenna. In

this case, it is necessary to move the Signal Antenna away from this window to another location.

You may also upgrade to an outdoor rated antenna (part # cant-0042) if mounting an antenna

outside is possible.

In order to capture the strongest signal, you may do one or all of the following:

1. Move the antenna around the window – higher is usually better.

2. Use the long suction cup attachments provided, in order to create a greater angle in which

to capture the signal. The suctions cups must be vertical on the window (as pictured, with

cable at the bottom – not on the side). Avoid draping the coax near the antenna.

3. Keep the Signal Antenna 2 feet from any metal.

KITCHEN

PATIO

MASTER

BEDROOM



SECOND: Place the zBoost Base Unit where you want to create a Cell Zone

Connect the Indoor Antenna and coax to the Base Unit and place it where you need signal. For the

widest possible signal area, it is recommended that you position the Base Unit near the middle of a

room or mount it on an interior wall. This Base Unit uses an omni-directional antenna that delivers

signal in a circular pattern around

the antenna. The zBoost CONNECT

does not require vertical separation;

however, the Signal Antenna and

Indoor Antenna should have

at least 15 feet of horizontal

separation. Increasing separation

of the 2 antennas will optimize

zBoost performance.

For best results, keep the Base Unit

off the ﬂ oor and at least 2 feet away

from other cords, metal objects

or other wireless devices such as

wireless routers or wireless access

points. The zBoost CONNECT

performs best when there are no

obstructions between the zBoost

Base Unit and your mobile device.

THIRD: Run the provided coaxial cable between the Base Unit and Signal

Antenna

Use the provided RG-6 coaxial cable to connect the Signal Antenna and the Base Unit. Coaxial

connections can loosen when the cable is moved. Be sure the connections stay hand-tight.

Should you need additional cable length, 15 foot extensions (Part #: YX030-15w) are available at

www.zBoost.com.

The total cable length should not exceed 65 feet. A longer

cable is helpful only if it allows you to place the Signal

Antenna in a location where you measure stronger signal.

FOURTH: Connect the zBoost Base Unit to the

provided power supply and plug into a power

outlet

Upon initial power up, the LED will cycle RED, GREEN

and ORANGE for 30 seconds. After 30 seconds, a series

of GREEN ﬂ ashes will indicate the quality of your setup.

Following this, a solid GREEN light indicates normal

conditions. If it is not solid GREEN, follow the instructions

in the Base Unit LED Indicators section. Adjustments

may be needed to optimize performance. If you ﬁ nd the

increased signal coverage is acceptable, however, no

additional adjustments are needed. See “zBoost Base

Unit Light Indicators” on page 7) for more information.

NOTE: The Base Unit can be plugged into a standard 2

or 3 prong 110 VAC receptacle using the Included power

supply. The power supply consumes less than 10W (less

than 0.2A AC).

zBoost Base Unit

Power Supply

Indoor Antenna

Coaxial Cable

Base Unit Bracket

zBoost Base Unit

Power Supply

Suction Cup

Attachments

Indoor

Antenna

Coaxial Cable

Signal Antenna

15 ft.

separation

1 2 3 4 5 6 7 8 9

Commentaires sur ces manuels

Pas de commentaire

ZBoost ZB540 Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs de signaux cellulaires ZBoost ZB540